End mills short, 1 tooth cut over centre, 30°, type NR, Weldon shank
D
k 12 |
d
h 6 | l1 | l2 | Z | Item code | On stock |
---|---|---|---|---|---|---|
6 | 6 | 57 | 13 | 4 | 124518.060 | Yes |
7 | 10 | 66 | 16 | 4 | 124518.070 | Yes |
8 | 10 | 69 | 19 | 4 | 124518.080 | Yes |
9 | 10 | 69 | 19 | 4 | 124518.090 | Yes |
10 | 10 | 72 | 22 | 4 | 124518.100 | Yes |
11 | 12 | 79 | 22 | 4 | 124518.110 | Yes |
12 | 12 | 83 | 26 | 4 | 124518.120 | Yes |
13 | 12 | 83 | 26 | 4 | 124518.130 | Yes |
14 | 12 | 83 | 26 | 4 | 124518.140 | Yes |
15 | 12 | 83 | 26 | 4 | 124518.150 | Yes |
16 | 16 | 92 | 32 | 4 | 124518.160 | Yes |
17 | 16 | 92 | 32 | 4 | 124518.170 | Yes |
18 | 16 | 92 | 32 | 4 | 124518.180 | Yes |
19 | 16 | 92 | 32 | 4 | 124518.190 | Yes |
20 | 20 | 104 | 38 | 4 | 124518.200 | Yes |
21 | 20 | 104 | 38 | 4 | 124518.210 | No |
22 | 20 | 104 | 38 | 5 | 124518.220 | Yes |
24 | 25 | 121 | 45 | 5 | 124518.240 | Yes |
25 | 25 | 121 | 45 | 5 | 124518.250 | No |
26 | 25 | 121 | 45 | 5 | 124518.260 | Yes |
28 | 25 | 121 | 45 | 5 | 124518.280 | Yes |
30 | 25 | 121 | 45 | 5 | 124518.300 | Yes |
32 | 32 | 133 | 53 | 6 | 124518.320 | Yes |
36 | 32 | 133 | 53 | 6 | 124518.360 | Yes |
40 | 32 | 143 | 63 | 6 | 124518.40032 | No |
D 40 ≠ DIN 844K
Cutting conditions
Material |
Strength |
Ap |
Ae |
Vc |
fz(mm/z) Ø 6 |
Ø 8 |
Ø 10 |
Ø 12 |
Ø 16 |
Ø 18 |
Ø 20 |
Ø 25 |
Ø 30 |
Ø 40 |
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
P.1 | Free-cutting steels, general construction steels | ≤ 600 N/mm² | 1,5xD | 0,5xD | 45 | 0.02 | 0.025 | 0.035 | 0.04 | 0.07 | 0.08 | 0.09 | 0.1 | 0.115 | 0.14 |
P.2 | General construction steels, steel castings | ≤ 850 N/mm² | 1,5xD | 0,5xD | 39 | 0.02 | 0.025 | 0.035 | 0.04 | 0.07 | 0.08 | 0.09 | 0.1 | 0.115 | 0.14 |
P.4 | Heat treatable steels | ≤ 900 N/mm² | 1,5xD | 0,5xD | 30 | 0.02 | 0.025 | 0.035 | 0.04 | 0.07 | 0.08 | 0.09 | 0.1 | 0.115 | 0.14 |
M.2 | Corrosion- and acid-proof steels | 750 - 850 N/mm² | 1,5xD | 0,5xD | 15 | 0.02 | 0.025 | 0.035 | 0.04 | 0.07 | 0.08 | 0.09 | 0.1 | 0.115 | 0.14 |
K.1 | Cast iron (≤ 240 HB) | ≤ 820 N/mm² | 1,5xD | 0,5xD | 35 | 0.02 | 0.025 | 0.035 | 0.04 | 0.07 | 0.08 | 0.09 | 0.1 | 0.115 | 0.14 |
Calculations of cutting conditions
Product attributes
Clamping element
more +Straight shank with clamping flat (Weldon) according to DIN 1835 B.
Tool geometry
more +Helix angle = 30°.
Rake angle = 12°.
Material HSS Co8
more +Extra high performance high speed steel with good toughness and great temperature resistance. It is applicable especially for milling of materials with high strength, austenitic steels, steels for warm working, etc.
Type NR
more +For roughing operation and materials of lower and medium strength (up to 700 MPa), surface roughness Ra 12,5 and more.