End mills long with corner radius, 2 teeth cut to centre, 35°-38°, type N, Weldon shank, coating AlCrN

Home
Catalogue
End mills long with corner radius, 2 teeth cut to centre, 35°-38°, type N, Weldon shank, coating AlCrN

S141612R Solid carbide (SC) DIN 6527L

Cutting conditions Product attributes

D h 10	d h 6	l₁	l₂	l₃	D_n	R	Z	Item code	On stock
6	6	57	13	19	5,7	0,5	4	S141612R.06005	No
6	6	57	13	19	5,7	1	4	S141612R.06010	No
8	8	63	19	25	7,6	0,5	4	S141612R.08005	Yes
8	8	63	19	25	7,6	1	4	S141612R.08010	No
10	10	72	22	30	9,5	0,5	4	S141612R.10005	No
10	10	72	22	30	9,5	1	4	S141612R.10010	Yes
10	10	72	22	30	9,5	2	4	S141612R.10020	No
12	12	83	26	36	11,5	0,5	4	S141612R.12005	Yes
12	12	83	26	36	11,5	1	4	S141612R.12010	No
12	12	83	26	36	11,5	2	4	S141612R.12020	Yes
16	16	92	32	42	15,5	0,5	4	S141612R.16005	No
16	16	92	32	42	15,5	1	4	S141612R.16010	No
16	16	92	32	42	15,5	2	4	S141612R.16020	No

Cutting conditions

Material	Strength	A_p	A_e	V_c	fz(mm/z) Ø 6	Ø 8	Ø 10	Ø 12	Ø 16
P.1 \| Free-cutting steels, general construction steels	≤ 600 N/mm²	1xD	0,3xD	210	0.015	0.015	0.02	0.02	0.025
P.3 \| Tool steels low alloyed	≤ 1100 N/mm²	1xD	0,3xD	175	0.015	0.015	0.02	0.02	0.025
P.5 \| Tool steels high alloyed	≤ 1100 N/mm²	1xD	0,3xD	120	0.015	0.015	0.02	0.02	0.025
M.1 \| Corrosion- and acid-proof steels	≤ 750 N/mm²	1xD	0,3xD	110	0.015	0.015	0.02	0.02	0.025
M.2 \| Corrosion- and acid-proof steels	750 - 850 N/mm²	1xD	0,3xD	90	0.015	0.015	0.02	0.02	0.025
K.1 \| Cast iron (≤ 240 HB)	≤ 820 N/mm²	1xD	0,3xD	150	0.015	0.015	0.02	0.02	0.025
K.2 \| Cast iron (> 240 HB)	> 800 N/mm²	1xD	0,3xD	110	0.015	0.015	0.02	0.02	0.025
S.1 \| Chrome-nickel alloys	≤ 1500 N/mm²	1xD	0,3xD	50	0.015	0.015	0.02	0.02	0.025
S.2 \| Titanium, titanium alloys	≤ 1250 N/mm²	1xD	0,3xD	70	0.015	0.015	0.02	0.02	0.025
H.1 \| Hardened materials (< 54 HRC)	≤ 1920 N/mm²	1xD	0,3xD	120	0.015	0.015	0.02	0.02	0.025
H.2 \| Hardened materials (54 - 60 HRC)	1920 - 2210N/mm²	1xD	0,3xD	100	0.015	0.015	0.02	0.02	0.025

Calculations of cutting conditions

Product attributes

Clamping element

more +

Straight shank with clamping flat (Weldon) according to DIN 6535 HB.

Tool geometry

more +

Helix angle = 35/38°. Rake angle = 10°.

End face design - radius

Solid carbide

more +

Carbide materials are characterised by high compressive strength, high hardness and therefore high wear resistance, but also limited flexural strength and toughness.

Type N

more +

Universal usage. Suitable for materials up to strength 900 MPa.

Feed direction possibility

Air cooling

AlCrN coating

more +

Coating with very high wear resistance and excellent hot hardness.